Components:

Front lights: 3/4 LED Recessed (amber lens, amber light)

3/4" Recessed Bullet LED Light - Amber Lens / Amber Light. Most of our kits ship with 3 lights per side which allows for a light to be installed around to the side for maximum visiblity.

Column mounted lever switch - silver

Rear T-Harness adds rear turn signal functionality to the factory tail lights. The harness Ts into the factory harness above the clutch cover. . Your vehicle needs to have the 4 pin plug shown in the photos below.

Adjustable flasher relay

Flasher relay with adjustable flash rate. Use the dial to adjust the flash rate. This flasher (CF3) can be replaced with the non adustable EP34 in a pinch. Installation: the relay should be mounted away from water. It is best to zip tie a plastic bag around the relay if you powerwash the interior of your vehicle.

Rear tail light tie-in harness

Rear T-Harness adds rear turn signal functionality to the factory tail lights. The harness Ts into the factory harness above the clutch cover. . Your vehicle needs to have the 4 pin plug shown in the photos below.

Features

Column mounted switch installs much easier than rocker or toggle switches and doesn't require any holes in your dash. Kit utilizes a heavy duty chrome plated column mounted turn signal switch ensuring natural feel and ease of use. Switch features built in indicators as well as hazard option. This is a beefy metal body switch....not a chrome-painted plastic unit!

2 plug and play harness assemblies complete the kit.

Uses factory brake lights and converts them for use as brake AND turn signal just like many automobiles. Front indicators (2 per side) mount into a 3/4" diameter hole to provide a clean  oem appearance.

Looking to add even more visibility to your front turn signals utilizing aftermarket LED lights or Fang lights? No problem, simply take our wire and connect it to your favorite front turn signal LED lights.

Specifications

Always consult your local and State laws if you intend to utilize this kit to make your machine street legal. Depending on the laws in your area this kit may or may not comply with street legal requirements.

Installation

Installation times will vary based on your familiarity with the vehicle. A beginner could plan on spending 5 hours on the install while an installer could plan on 20 to 30 minutes.

Fits 18-19 Polaris Ranger 1000 non ride command and all year General with 4 pin tail light bed plug.
Extended harness fits both 2 and 4 seat units
Check bed-to-frame plug at top rear of frame under the bed to verify fitment. This is the center connection where both left and right tail lights come together near center of the rear frame area of machine. NOT THE PLUG AT THE ACTUAL TAIL LIGHTS!
On Ranger and General models, lift bed to examine top rear driver side frame area.
 

Painfully simple to install. Only requires 12v+ and 12v- connection to machine.

A pulse power harness is included for newer machines with the pulse bar system.

All components terminated with connectors allowing for full plug and play operation.

Rear T harness plugs into factory 4 pin plug and utilizes the rear brake lights as turn signals. This harness easily feeds from rear of machine through tunnel and up into hood compartment where it feeds through firewall into dash and plugs into the turn signal switch. A complete front end harness with sealed LED lights feeds through firewall into dash and also plugs into the turn signal switch.

Total install time approx 1 hour.

Description

MCSADVENTURES turn signal kit

Plug and Play utilizing factory brake lights

Fits all Polaris General models 2016+

(also fits many 2018+ Ranger 1000 non-command models...must have 4  pin plug under the bed)

Extended length harness fits 2 and 4 seat models

Includes Pulse bar harness for newer 2019+ machines.

 amber/amber front lights

!!Must have the 4 pin plug shown in picture on top of engine under the bed!!

*****check your machine to verify fitment by looking for the bed-to-frame tail light harness plug located near the top rear frame on top of the engine underneath the bed*****

This is the center connection where both left and right tail lights come together near center of the rear frame area of machine. NOT THE PLUG AT THE ACTUAL TAIL LIGHTS!

Looking for a true plug and play for your Ranger or General that utilizes the factory tail lights?

We've designed a great plug n play solution at a very reasonable price.