Components:

Front lights: 3/4 LED Recessed (amber lens, amber light)

3/4" Recessed Bullet LED Light - Amber Lens / Amber Light. Most of our kits ship with 3 lights per side which allows for a light to be installed around to the side for maximum visiblity.

---

Front lights: Bolt On LED (clear lens, amber light)

Bolt on style LED strip. Clear lens with amber light. Can be bolted on or installed through the grill.

---

Adjustable flasher relay

Flasher relay with adjustable flash rate. Use the dial to adjust the flash rate. This flasher (CF3) can be replaced with the non adustable EP34 in a pinch. Installation: the relay should be mounted away from water. It is best to zip tie a plastic bag around the relay if you powerwash the interior of your vehicle.

---

Dash cluster tie-in

If you have the instrument cluster pictured, you may wish to utilize our cluster tie-in kit to utilize the indicator arrows in your OEM gauge. Simply snap the pins from our harness into the factory plug housing. Note: may not be compatible with all machines even with this cluster (example: 2018 Ranger won't work). If you choose to utilize this feature, a complete test should be performed with machine off and machine running prior to installation. Most issues with installing the cluster harness can be solved by pressing the harness pins further into the housing. The pins may click before they are fully seated. Green led indicators are included for those unable to take advantage of the cluster tie-in. more info here

---

Rear tail light tie-in harness

Rear T-Harness adds rear turn signal functionality to the factory tail lights. The harness Ts into the factory harness at each rear tail light. Your vehicle needs to have tail lights with the 4 pin plug shown in the photos below.

---

Accessory power plug tie-in

For vehicles equipped with an accessory power bar. This power plug can be attached to the turn signal kit harness using the provided connectors.

---

Features

Kit is comprised of a complete switch/control module front harness which connects to a rear T harness.

Rocker switch harnesses are prewired into the main control module and simply plug onto the back of the rocker switch. No fumbling with qd terminals.

Blue illuminated Left / Right rocker lights up with key on and also flashes when selected thus indicating direction.

Includes optional instrument cluster integration for machines with the instrument cluster shown.

A custom rear T harness plugs into the left and right factory tail lights and converts the factory brake lights for use as brake AND turn signals. We also supply a license plate light pigtail that can activate your license plate light with key on.

 

Looking to add even more visibility to your front turn signals utilizing aftermarket LED lights or Fang lights? No problem, simply take our wire and connect it to your favorite front turn signal LED lights.

All plug and play. Everything plugs together.

Only 3 connections to the vehicle:     12v+ batt     12v+ keyed (ignition)      12v- (ground)

Specifications

Always consult your local and State laws if you intend to utilize this kit to make your machine street legal. Depending on the laws in your area this kit may or may not comply with street legal requirements.

 

MADE IN THE USA

Installation

Installation times will vary based on your familiarity with the vehicle. A beginner could plan on spending 5 hours on the install while an installer could plan on 20 to 30 minutes.

Painfully simple to install. All components terminated with connectors allowing for full plug and play operation.

Rear T harness plugs into the left and right tail lights utilizing the rear brake lights as turn signals. This custom harness feeds from the rear of machine through tunnel and up into hood compartment where it feeds through firewall into dash and plugs into the control module

A complete front end harness with sealed LED lights feeds through firewall into dash and also plugs into the control module.

For power only 3 connections to the machine are required:   12v+ batt   12v+  keyed ignition    12v-ground

A pulse power harness is included for machines with the pulse power bar.

Total install time:  approx 1 hour

 

Photos

Description

MCSADVENTURES Rocker turn signal kit

Fits 2024 RZR XP 1000

Rocker switch snaps into .83 X 1.48 cutout

Plug and Play utilizing factory brake lights

Custom rear T harness plugs into the left and right tail light harness

Extended length harness fits 2 and 4 seat models

Includes Pulse bar harness for newer 2019+ machines.

Bolt on LED lights for front turn signals

Looking for a true plug and play way to add turn signals to your  2024 RZR XP 1000  that utilizes the factory tail lights?

We've designed a great plug n play solution at a very reasonable price.